7. Commands to Configure Radio Operation
| Command | Command Description | Parameters | Factory Default |
| ATBD | Baud Rate – Sets serial com port baud rate (bps). Over-the-air (throughput) baud rate is set with ATR2 command.If a PC’s serial baud rate is set higher than the fixed over-the-air baud rate of the module, hardware handshaking may be required. | Range: 0 – 70 = 1200 5= 38400 1 = 2400 6=57600 2 = 4800 7=115200 3 = 9600 4 = 19200 | 3 |
| ATDT | Destination Address to call– Sets address of the modem to send data to. Note, this parameter is entered in HEX format. Each digit may be a 0,1,2,3,4,5,6,7,8,9,A,B,C,D,E,or an F. | Range: 0-FFFF | 1234 |
| ATF | Display frequencies – Display all of the frequencies programmed into all of the channel memories. | N/A | |
| ATFT | Transmit Frequency – Program the transmit frequency for this channel. Enter in Hz or in MHz. The frequency will automatically be saved in non-volatile memory (flash) for this current channel number. | Range: See product data sheet. For MURS products, frequency cannot be changed. | See product data sheet. |
| ATFR | Receive Frequency – Program the receive frequency for this channel. Enter in Hz or MHz. The frequency will automatically be saved in non-volatile memory (flash) for this current channel number. | Range: See product data sheet. For MURS products, frequency cannot be changed. | See product data sheet. |
| ATFX | TX and RX Frequency – Program the receive and transmit frequency for this channel. Enter in Hz or MHz. Same as issuing an ATFR and an ATFT command. The frequency will automatically be saved in non-volatile memory (flash) for this current channel number. | Range: See product data sheet. | N/A |
| ATHP | Channel Number – Select separate channels to minimize interference between multiple sets of modules operating in the same vicinity. | Range: 1 – 6 | 1 |
| ATMK | Address Mask – Configures local and global address space. Each digit may be a 0,1,2,3,4,5,6,7,8,9. | Range: 0000 – FFFF | FFFF |
| ATMY | Unit Address – Configures the individual; address for this unit. Each digit may be a 0,1,2,3,4,5,6,7,8,9. | Range: 0000 – FFFF | 1234 |
| ATPO | RF Power Output. Set or show the RF power output setting. Value is in percent, from 0% to 100%. Use and RF wattmeter to confirm the power setting, and adjust the % accordingly to obtain the desired RF power level. | 0-100 | 100 |
| ATR2 | Over-The-Air bit rate – This is the data rate the radio uses to send data over the air. All RF modems in the network must use the same over-the-air baud rate. Refer to section Error! Reference source not found. for information on how to set the OTA baud rate. | Range: 0 = 800 7 = 5142 2L5 = 9600 2L 3 = 48001 = 1200 8 = 9600 4L 6 = 19200 4L 4 = 8000 4L 2 = 2400 9 = 2000 2L | 3 |
| ATRV | Disable Remote Access – When enabled (set to a 0), the modem will respond to over-the-air RPR requests, Pings, and over-the-air commands. | 0 = Remote Access on 1 = Remote Access disabled | 1 |
| ATSL | Serial Number – Reads and returns a unique serial number for thjs unit. | Read Only1 – 999999999 | unique |
| ATSH or SHOW | Show – Display the configuration of the modem. This will return a page of ASCII characters, showing the main configuration parameters. | none | None |
| ATST | Statistics – Show the unit’s operational statistics. See Statistics section of user manual. | 0, 1,2, 3, 4, or 5 | None |
| ATVB | Read DC input Voltage– Returns the DC input voltage reading, in mV (12500 = 12.5VDC input). | None | none |
| ATVR | Firmware Version – Returns firmware version currently loaded on the module. | Read Only, 3 characters | Current version |
| REPEAT n | Enable/Disable Store and Forward Repeating – 0=disabled, 1 – enabled (repeat everything) | 0 or 1 | 0 (Off) |
| PING | Ping another modem. Format is PING xxxx, where xxxx is the ID of the modem to ping. If remote access is enabled on xxxx, it will respond. | XXXX | – |
| SHOW | Show/display an overview of the radio’s configuration. | None | – |
** indicates values that are calibrated in the factory and are unit-specific. If the “Radio Type” is changed, these will need to be re-calibrated.
- GPS Additional Commands to Configure GPS and Tracking Features
The following commands are unique to the –GX version of the M7. When you execute any of these commands, the new parameter is automatically stored in EEPROM.
| Command | Command Description | Parameters | Default |
| GX | Display GPS settings. Show an overview of the current GPS features and configurations in the M7 GX. | – | – |
| GPS | GPS Operation Mode. Read/Set the GX version’s Operating mode. | 0 – 6 | 1 |
| GPS&F | Reset all GPS (-GX version) parameters. Set the GX version’s Operating mode to GPS mode 4, and sets all GPS parameters to factory defaults. It does not erase frequency or other radio-related parameters. | – | – |
| IDLERATE | IDLE TX Interval. Set the number of seconds between position transmissions when the unit is idle (has not moved more than TRIGDX meters). | 0-9999 seconds | 10 |
| KEYPHRASE | Privacy Security Key Code. Set the privacy key for this device. It must be the same key as used on all other Raveon products in your system. It secures radio transmissions from unauthorized reception. Set it to 0 to disable security encryption of data. | 2-16 ASCII characters. | “RAVEON” |
| PREFIX | ID Prefix. Set an ID prefix. The prefix is 1-8 characters that will be put in front of the ID when reporting an ID as a waypoint name. A dash means no prefix. Default is a capitol letter V. | 1-8 ASCII characters Set it to “0” for no prefix. | V |
| SLOTTIME | TDMA Slot duration. Configure the width of a TDMA slot. 50mS increments. | 50 – 1000 | 200 |
| SLOTNUM | TDMA Slot Number. Configure the slot number that this radio will use to send its data in. | 1-9999 | The MYID of the unit |
| TRIGBITS | I/O Change Reporting. Which bits are used as transmission triggers. This is a HEX number. Bit 0 is IN0, bit 1 is IN1…. | 0-FF | 0 |
| TDMATIME | Set/read TDMA Frame time. The length of one TDMA time frame, in seconds. M7’s may transmit once per frame, and only in their preset time-slot. | 1-3599 | 10 |
| TRIGPOL | Polarity of the input bits. 0 = normal active high operation(causes unit to transmit when it goes high), 1 = Inverted, active low. This is a HEX number. Bit 0 is IN0, bit 1 is IN1…. | 0-FF | 0 Active high |
| TRIGEX | Report on change. Sets which input bits cause a report on change. If a particular bit is a 1, then it will trigger a report when it changes. The input bit must also be enable with the TRIGBITS. This is a HEX number. Bit 0 is IN0, bit 1 is IN1… | 0-FF | 0 |
| TRIGDX | Distance trigger. Set a distance (in meters) threshold beyond-which the unit will transmit its position and status. If set to 0, the unit always reports at the TXRATE. If set to an distance greater than zero, then the unit reports at the TXRATE intervals if it has moved this distance since the last report. If it has not moved, it will still report its position, but at the rate set by IDLERATE. If IDLERATE is set t 0, then the unit will not report its position when not moving. | 0-999 | 0 |
| TRIGSPEED | Speeding Report. Set a speed (in kilometers/hour) threshold above-which the unit will begin reporting its position and status. Set to 0 to disable this feature. | 0-999 | 0 |
| TXRATE | GPS Report Rate. Set number of seconds between GPS reports. This is also the rate at which the internal GPS will measure position, speed, etc. Even if the unit is not moving, the GPS periodically measures position and speed to determine if it has triggered a speed or position transmission. | 1 – 9999 | 10 |
For the UHF M7 GX model RV-M7-UC-GX, the factory defaults GPS settings are:
Radio channel 1 464.500 MHz Slot Number The same ID
GPS Mode 4 (GPS display) ID Prefix V
Over-the-air baud rate: 4800 baud, 2-level I/O Change reporting 0, off
Serial port 4800 N/8/1 Proximity Alert 0, off
Hardware flow control Off Security KEY RAVEON
RF Power Output 5 watts Position report interval 10 seconds
Channel number 1
